Used approximately 8,000 TPD cane processing equipment, including:
**MILL #2**
1. Two (2) complete four-roll vertical housing assemblies, Bancroft cast steel
a. Type 39” x 78”
b. Face 18”
c. Distance between housings 106 ¼”
2. Two (2) complete cap sets (Require repair)
a. Piston diameter 12”
b. Top roll maximum displacement 1”
3. One (1) turnbeam with turnplate mounting bolts to suit housing centreline, with adjusting and locking system
4. Two (2) top bearing sets, box cast bronze
5. Four (4) bottom bearing sets, box cast steel
6. One (1) press roll assembly
a. Shell diameter 32 ½”, length 76 3⁄8”, pitch 2”
b. Crown wheel driving 55 ¼” diam. ext., 8 ¾” face, 20 tooth
c. Crown wheel driven 43 ¼” diam. ext., 8 ¾” face, 15 tooth
7. One (1) top roll assembly
a. Shell diameter 38 ½”, length 78”, 3” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
8. One (1) bagasse roll assembly
a. Shell diameter 38”, length 78”, 3” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
9. One (1) cane roll assembly
a. Shell diameter 38”, length 78”, 3” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
**MILL #3**
1. Two (2) complete four-roll vertical housing assemblies, Bancroft cast steel
a. Type 39” x 78”
b. Face 18”
c. Distance between housings 106 ¼”
2. Two (2) complete cap sets
a. Piston diameter 12”
b. Top roll maximum displacement 1”
3. One (1) turnbeam with turnplate mounting bolts to suit housing centreline, with adjusting and locking system
4. One (1) turnplate 78”, 18” width, 2 ½” pitch
5. Two (2) top bearing sets, box cast bronze
6. Four (4) bottom bearing sets, box cast steel
7. One (1) press roll assembly
a. Shell diameter 31 3⁄8”, length 76 3⁄8”, pitch 2”
b. Crown wheel driving 55 ¼” diam. ext., 8 ¾” face, 20 tooth
c. Crown wheel driven 43 ¼” diam. ext., 8 ¾” face, 15 tooth
8. One (1) top roll assembly
a. Shell diameter 38 ½”, length 78”, 2 ½” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
9. One (1) bagasse roll assembly
a. Shell diameter 38 ¼”, length 78”, 2 ½” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
10. One (1) cane roll assembly
a. Shell diameter 38 ½”, length 78”, 2 ½” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
**MILL #4**
1. Two (2) complete four-roll vertical housing assemblies, Bancroft cast steel
a. Type 39” x 78”
b. Face 16”
c. Distance between housings 106 ¼”
2. Two (2) complete cap sets
a. Piston diameter 12”
b. Top roll maximum displacement 1”
3. One (1) turnbeam with turnplate mounting bolts to suit housing centreline, with adjusting and locking system
4. Two (2) top bearing sets, box cast bronze
5. Four (4) bottom bearing sets, box cast steel
6. One (1) press roll assembly
a. Shell diameter 32”
b. Shell length 76 3⁄8”, pitch 2”
c. Crown wheel driving 53 ½” diam. ext., 8 ¾” face, 20 tooth
d. Crown wheel driven 41 ½” diam. ext., 8 ¾” face, 15 tooth
7. One (1) top roll assembly
a. Shell diameter 38 ½”, length 78”, 2 ½” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
8. One (1) bagasse roll assembly
a. Shell diameter 38”, length 78”, 2 ½” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth
9. One (1) cane roll assembly
a. Shell diameter 38”, length 78”, 2 ½” pitch
b. Crown wheel 43” diam. ext., face 16”, 17 tooth (Used in good condition)
**MILL #5**
1. Two (2) complete four-roll vertical housing assemblies, Bancroft cast steel
a. Type 39” x 78”
b. Face 16”
c. Distance between housings 106 ¼”
2. Two (2) pistons diameter 12”, top roll maximum displacement 1” (Require repair)
3. One (1) turnbeam with turnplate mounting bolts to suit housing centreline, with adjusting and locking system
4. Two (2) top bearing sets, box cast bronze
5. Four (4) bottom bearing sets, box cast steel
6. One (1) press roll assembly
d. Shell diameter 33 3⁄8”, length 76 3⁄8”, pitch 2”
e. Crown wheel driving 55 ½” diam. ext., 8 ¾” face, 20 tooth
f. Crown wheel driven 41 ½” diam. ext., 8 ¾” face, 15 tooth
7. One (1) LOTUS XP top roll assembly, used only 3 months
g. Shell diameter 38 ½”, length 78”, 2 ½” pitch
h. Crown wheel 43” diam. ext., face 16”, 17 tooth
8. One (1) bagasse roll assembly
i. Shell diameter 38 ¼”, length 78”, 2 ½” pitch
j. Crown wheel 43” diam. ext., face 16”, 17 tooth (Used in good condition)
9. One (1) cane roll assembly
k. Shell diameter 37 ¾”, length 78”, 2 ½” pitch
l. Crown wheel 43” diam. ext., face 16”, 17 tooth (Used in good condition)
**SPARE LIST**
1. Seven (7) crown wheels, 43” diam. ext., face 16”, 17 tooth (Mills 2, 3, 4, 5)
2. Three (3) new crown wheels, 43” diam. ext., face 16”, 17 tooth (Mills 2, 3, 4, 5)
3. One (1) top roll, shell length 78”, 3” pitch
4. Two (2) top rolls, shell length 78”, 2 ½” pitch
5. Four (4) lower shafts with 18” x 22” journals for Bancroft housing
6. One (1) top shaft with 18” x 22” journals for Bancroft housing
7. One (1) top L scraper, 3” pitch
8. One (1) top L scraper, 2 ½” pitch
9. Two (2) press roll mini turnplate assemblies, 2” pitch (New)
---
**Notes:**
- Measurements remain imperial as per original.
- Adjusted spelling to British English: "centreline" to "centreline", "repair" noted as "require repair."
- Standardised capitalisation and consistency of terms (e.g. "pitch," "diam. ext.," "face").
- Hyphenated compound adjectives (e.g. "four-roll vertical housing assemblies").
- Used commas to separate descriptors in lists for better clarity.
We use cookies to improve your experience. Privacy Policy.